Copy Trading Configurations
Last updated
Last updated
Min - If you choose to have the Min mode enabled, the bot will decide the amount to buy between two amounts - your Max Amount that you have set in the bot, and the amount of the wallet that you are copying. The bot will choose whichever value is lower out of the two.
For example, you have Max Amount set at 1 ETH, and the wallet that you are copying buys with 2 ETH, so the bot will buy 1 ETH, as it is the lower value of the two. If you have Max Amount set at 1 ETH, and the wallet that you are copying buys with 0.5 ETH, so the bot will buy 0.5 ETH, as it is the lower value of the two.
Max - If you choose to have the Max mode enabled, bot will only buy up to your Max Amount.
For example, you have Max Amount set at 1 ETH, and the wallet that you are copying buys with 2 ETH, so the bot will buy 1 ETH. If you have Max Amount set at 1 ETH, and the wallet that you are copying buys with 0.5 ETH, so the bot will buy 1 ETH.
Copy Sell will let you mirror the sells of the wallet that you are copying. You can select the desired amount that you wish to copy. For example, if you would like to leave a moonbag for all the tokens the wallet buys, just set 80-90% on the Copy Sell setting. The wallet you are copying will have sold all of his tokens, but you will still have 10-20% remaining.
Select the amount of Gas you would like to use for your transactions. The more Gas you use, the better position in the block you will get, but the transaction will cost you more.
There are a few interesting settings that need some extra explanation:
AntiRug (not available on some chains) is an all-in-one protection from all the things that are nasty - rugs, taxes, blacklists and everything in-between. You can enable/disable it by clicking this button:
AntiRug will sell on high-impact sells, for example if dev dumps 10 wallets at once, the bot will frontrun these transactions.
Red is disabled, green is enabled.
Buy/Sell Tax - maximum amount of tax that your poor soul can tolerate. If buy/sell of a token is higher than your set amounts, your transactions will not be sent. Transactions will be sent when the requirements are met.
For example, you have set Buy Tax at 10%, Sell Tax at 5%, the developer launches with 2% buy tax, which complies with your settings, and 7% sell tax, which is the reason why your transactions will not be sent. Transactions will be sent when the requirements are met.
Min Wallet Balance - This USD value controls the minimum amount of balance a wallet should hold for a buy to trigger. If balance is below this threshold a buy will not trigger.
Min Liquidity - if the token developer adds an amount lower than you specified to the liquidity pool, your transactions will not be sent. Transactions will be sent when the requirements are met. Amount is written in USD.
For example, you have set Min Liquidity at 1000, and the developer adds 0.2 ETH to liquidity, in that case, your transactions will not be sent. Transactions will be sent when the requirements are met.
Alpha mode disables all of the security checks of the bot and lets you buy into high taxes, honeypots, blacklists etc., etc. Red is disabled, green is enabled.
Buy Once - You will buy a token only one time. If the wallet you are copy trading buys the same token multiple times, you will only copy the first purchase. Red is disabled, green is enabled.
Min Mcap - This sets the minimum market cap of a token in order to trigger the copy trade. If the market cap is below this value and this setting is active, the buy will not trigger. Amount is written in USD.
Max Mcap - This sets the maximum market cap that a token can have. If market cap is above this value and this setting is active, the buy will not trigger. Amount is written in USD.
Slippage is calculated after taxes. For example, if you plan to buy a token with 1 ETH, and there's a 50% tax on the token, your initial 1 ETH will be reduced to 0.5 ETH due to the tax. Then, the slippage is applied. Consequently, the actual minimum amount you'll end up buying may be much less than 0.5 ETH. For tax protection you can select the maximum buy and sell taxes in the settings.
Slippage is calculated not on token price fluctuation, but on the amount you are trying to buy. For example: You are trying to buy 1 Eth worth of Pepe and you have slippage set at 50%. This means that right after buying you are accepting that your tokens will be worth anywhere from 0.5 Eth to 1 Eth (if taxes are at 0%)
Keep in mind, there is no anti-mev on Binance Smart Chain, so please use Slippage!
